ASA Petitions FAA for Extension of DAR-56 Program

Last week ASA submitted a petition to the FAA formally requesting the indefinite extension of the Limited DAR-F Program for Accredited Distributors–commonly known as the DAR-56 program–that is scheduled to expire September 30, 2017.  ASA further requested an expansion of the program to better reflect the needs of the distribution community.  You may also recall that ASA recently led an industry effort that secured the reissuance of FAA Notice 8900.380 for another year. Both of these efforts are in response to the 8130-3 tag requirements arising out of MAG 6, which put billions of dollars of distributor inventory at risk.

ASA explained in its petition to extend DAR-56 indefinitely that the facts that gave rise to the need for the DAR-56 program have not changed and that the need for the program to continue was therefore very important to distributors.  The DAR-56 program permits Limited DAR-F’s to issue 8130-3 tags for parts on the basis of specific indicia of sourcing from the PAH.

As attendees of the ASA conference heard from members, distributors have so much inventory that needs to be tagged under the DAR-56 program that it could literally take years to tag every part.  This includes vast numbers of small, low-dollar-value parts for which hiring an independent designee would be economically infeasible.  ASA therefore proposed an indefinite extension of the program with semi-annual meetings between the FAA, ASA, and interested parties to discuss the ongoing need for the program so that it can be discontinued after a permanent solution is developed.

In addition to proposing an indefinite extension of the DAR-56 program (rather than annual extensions requiring yearly petitions and discussions), ASA also recommended changes that would improve the effectiveness of the program and help distributors.

At present, the DAR-56 program permits Limited DAR-F’s to issue 8130-3 tags under the following criteria:

  1. The aircraft part was received by the distributor prior to November 1, 2016 and
  2. The aircraft part must bear specific indicia of production under 14 C.F.R. Part 21:
    1. A certificate or statement of conformity that was issued by the production approval holder (any documentation part numbers and serial numbers, if applicable, must match any part markings); or,
    2. A certificate or statement of conformity that was issued by the production approval holder’s supplier, and a verification of direct shipment authorization; or,
    3. Markings regulated under 14 C.F.R. 45.15 and describing the PAH’s name or other identification (for parts, this would typically be limited to PMA, TSOA or critical parts).

ASA recommended that the program be extended as follows:

  1. The program be expanded to include any aircraft part that was received by the distributor at any time when the distributor was accredited under the AC 00-56 program.
  2. Expand the acceptable indicia of production under an FAA production approval to include other documentation the FAA has previously recognized:
    1. For an aircraft part that was accepted into an air carrier’s inventory system as new article, and then subsequently released from that air carrier’s inventory system, a document from the air carrier identifying the part by part number, and by serial number where appropriate, and identifying the part as new (including new surplus); or
    2. A maintenance release document showing (i) that the part was inspected under 14 C.F.R. Part 43 by a person authorized to approve such work for return to service, (ii) that the part was found to be in new condition, and (iii) a part number that matches a number known to be a PAH part number, and that matches the part number on the part, where applicable.

These proposed expansions reflect the fact that the November 1, 2016 receipt date appeared wholly arbitrary and neither supported nor required by any regulatory basis, and that the two additional forms of documentation are commonly accepted in the industry under Part 21 of the regulations.  This would solve the problem of those parts that are currently still being received without tags (as they continue to be released from PAH’s who do not issue tags, or as new surplus from air carriers without tags) and those parts that currently have PAH documentation but are nonetheless excluded under the terms of the current program.

ASA appreciates the FAA’s collaborative efforts to work with us to extend the DAR-56 program as we work toward a permanent solution to the MAG 6 8130-3 tag issue.  We will keep our members updated as we hear more from the FAA.

 

Advertisements

One Response to ASA Petitions FAA for Extension of DAR-56 Program

  1. Pingback: DAR 56 Extended Until August 2018 – Submit Your Request For Extension NOW! | ASA Web Log

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: